Forecr’s DSBOARD-ORNX v1.0 is industrial carrier board based on Nvidia Jetson Orin NX and Orin Nano processor modules for edge analytics. It is compatible with multi stream deep learning applications.

TECHNICAL SPECIFICATIONS

NVIDIA Jetson Orin NX and Orin Nano SoM option

1x HDMI 2.0 (max resolution 3840x2160)

1x Gigabit Ethernet

2x USB 3.1 Type-A

1x CAN Bus

4x CSI Connectors (2x 2-lane, 2x 2-lane or 4-lane)

1x RS232

1x RS422

Fan Connector

RTC Battery Connector

SIMCard Connector

Serial Communication Connector (1x I2S, 1x I2C, 1x SPI)

1x microUSB2.0 (software recovery)

2x M.2 Type-M Key (1x 2230, 1x 2280)

1x M.2 Key-B Slot

1x M.2 Key-E Slot

9-28 VDC Input

OS: Ubuntu Linux 20.04

Dimensions: 100 mm x 100 mm

DSBOARD-ORNX Power Button

The DSBOARD-ORNX implements a power button for energize the platform. It is located on the front side of the board.

DSBOARD-ORNX Recovery Pushbutton

The DSBOARD-ORNX implements a recovery pushbutton. Recovery button should be pressed with reset button at the same time. After released reset button, recovery button should be pressed a little bit more (min. 250 ms). It is located on the front side of the board.

DSBOARD-ORNX Reset Pushbutton

The DSBOARD-ORNX implements a reset button. It is recommended to use needle-like material. It is located on the front side of the board.

DSBOARD-ORNX Power Connector

The DSBOARD-ORNX implements 4-Pin Power Terminal Connector that accepts +9V to +28V DC power. The mating connector is "1708595". The first and the third pins are positive , second and fourth pins are negative. The power connector is located on the rear side of the board.

DSBOARD-ORNX SIM Card Connector

The DSBOARD-ORNX implements a nano SIM card connector. It is located on the bottom side of the board.

DSBOARD-ORNX M.2 Key-M Connectors

The DSBOARD-ORNX implements two M.2 M-Key Connector(1x 2230, 1x 2280) for suitable modules. M.2 2280 slot is located on front side and M.2 2230 slot is located on bottom side of the board.

DSBOARD-ORNX M.2 Key-B Connector

The DSBOARD-ORNX implements a M.2 Key-B Connector for suitable modules. The M.2 Key-B connector is located on the front side of the board.

DSBOARD-ORNX M.2 Key-E Connector

The DSBOARD-ORNX implements a M.2 E-Key Connector for suitable modules. This connector is located on the bottom side of the board.

DSBOARD-ORNX CSI Connectors

The DSBOARD-ORNX implements 4 CSI connectors. 2 at front (CAM1, CAM3 - 686115148922 from Würth Elektronik), 2 at bottom (CAM0, CAM2 - 687122149022 from Würth Elektronik). The bottom connectors can be used as 4-lane and 2-lane. The front connectors can be used as just 2-lane. The connector’s possible connections shown by below.

DSBOARD-ORNX I/O Terminal Connector

The DSBOARD-ORNX implements 14 pins GPIO Expansion connector which has 3 digital output pins, 2 digital input pins, RS232-RS422 & CANBus pins. The mating connector is “1790344” (DFMC 1,5/ 7-STF-3,5) produced by Phoenix Contact.

DSBOARD-ORNX Serial Communication Connector

The DSBOARD-ORNX implements 16 pins Serial Communication connector which has SPI, I2C and I2S standard pins. All signals are the 3.3V voltage level. The connector type is "DF11-16DP-2DSA(24)" . The mating connector is "DF11-16DS-2C". The small arrow represent the first pin and the opposite of this pin is second pin . It is located on the front side of the board.

DSBOARD-ORNX Panel Connector

The power, recovery & reset button's signals located at the panel connector. The connector type is "53398-0871". The mating connector is "51021-0800" produced by Molex.

DSBOARD-ORNX RTC Battery Connector

The DSBOARD-ORNX implements a RTC battery holder. The connector is suitable for CR1220 batteries. The connector is located on front side of the board.

DSBOARD-ORNX HDMI Connector

The NVIDIA® Jetson Orin NX module will output video via the DSBOARD-ORNX vertical HDMI connector that is HDMI 2.0 capable. It is located on the rear side of the board.

DSBOARD-ORNX USB 3.1 Type-A Connector

The DSBOARD-ORNX incorporates 2 USB 3.1 Type-A connectors with a 1.5A current limit per connector. The USB connector is located on the rear side of the board.

DSBOARD-ORNX 10/100/1000 Ethernet Connector

The DSBOARD-ORNX implements RJ-45 ethernet connector for internet communication. RJ-45 connector is connected directly to the NVIDIA Jetson module. The ethernet connector is located on the rear side of the board.

DSBOARD-ORNX Fan Connector

The DSBOARD-ORNX implements a fan connector as 53398-0471 from Molex. The mating connector is 0510210400. It is located on the bottom side of the board.

DSBOARD-ORNX Recovery Mode Micro USB Connector

The DSBOARD-ORNX implements a Micro USB connector to allow to install or upgrade the operating system. It is located on the front side of the board. 

DSBOARD-ORNX Debug Mode Header Connector

The DSBOARD-ORNX implements a header connector to access the module by using TTL connection. It is located on the front side of the board.

Thank you for reading our blog post.